| Pin | Typical Wire Color | Function | Notes / Conditions | |-----|--------------------|-----------------------------------------------|----------------------------------------------| | 1 | Red/Yellow | Permanent battery voltage (ECU main power) | 30a, fused | | 2 | Brown | ECU ground (main chassis ground) | GND, connects to engine block / chassis | | 3 | Black/Yellow | Ignition switched power (15) | Provides +12V when key is in ON/START | | 4 | - | Not connected | | | 5 | - | Not connected | | | 6 | Grey/Red | Throttle position sensor (TPS) – signal | Linear 0-5V output | | 7 | Brown/Green | Intake air temperature (IAT) – sensor ground | Shared sensor ground | | 8 | Yellow/Black | Engine speed sensor (RPM) – signal positive | Variable reluctance sensor | | 9 | Yellow/Blue | Engine speed sensor – signal negative | | | 10 | Blue/Black | Knock sensor – signal | Shielded wire | | 11 | Green | Injector cylinder 3 – control (ground switch) | Low-side output | | 12 | Grey/White | Injector cylinder 1 – control | | | 13 | Green/Yellow | Fuel pump relay control | Activates relay (ground trigger) | | 14 | Green/White | EGR valve (if equipped) – control | PWM output | | 15 | Black/Green | Secondary air injection relay (if equipped) | Ground trigger | | 16 | White/Green | Ignition coil – cylinder 1 & 4 control | Waste-spark ignition (paired) | | 17 | White/Black | Ignition coil – cylinder 2 & 3 control | Waste-spark ignition (paired) | | 18 | Brown/Yellow | Lambda (O2) sensor – heater ground | Shared sensor return | | 19 | White/Yellow | Lambda (O2) sensor – signal (bank 1) | 0-1V narrowband | | 20 | Blue/White | Coolant temperature sensor – signal | NTC sensor, voltage divider | | 21 | - | Not used | | | 22 | Brown/Red | Engine speed sensor – shield / ground | | | 23 | Blue/Grey | Injector cylinder 4 – control | | | 24 | Brown/Black | Injector cylinder 2 – control | | | 25 | Black/Grey | Idle air control (IAC / idle stepper) – coil A| Bipolar stepper motor | | 26 | Brown/White | IAC – coil B | | | 27 | Black/Blue | IAC – coil C | | | 28 | Brown/Red | IAC – coil D | | | 29 | White/Grey | MAP sensor – signal (if speed-density system) | 0-5V output | | 30 | Brown/Blue | MAP sensor – ground | | | 31 | Yellow/Grey | Oxygen sensor heater – control (ground side) | PWM driven | | 32 | Blue/Yellow | Camshaft position sensor (if equipped) – signal| Used for sequential injection (late SIMOS 33A)|
Are you trying to do a or a full boot-mode recovery ? What is the exact part number printed on your ECU sticker? Share public link simos 33a pinout top
Never rely on a single source. Cross-reference any pinout you find with multiple forum threads or official documentation. If possible, use a multimeter to verify power and ground pins before connecting any external devices. | Pin | Typical Wire Color | Function
The physical ECU unit typically carries part numbers like 06A906033 or 06A906033xx and the internal hardware is often identified by a starting with 5WP4xxxx , such as 5WP40019 05 or 5WP40019 07 . This makes it a close relative of the SIMOS 3PC and other SIMOS 3.3 variants that share much of the same core architecture and pinout philosophy. Cross-reference any pinout you find with multiple forum
: Inputs from piezo-resistive sensors on the engine block to prevent pre-ignition damage. Coolant and Oil Temperature